STEIN TEC® Bedding Mortar BM 04 is a hydraulically binding work dry mortar with application-specific mineral and organic additives. STEIN TEC® Bedding Mortar BM 04 is available as bag ware (40 kg), as Big Bag (1.000 kg) and/or from 15 t in the silo with mixing device. Due to its high adhesive tensile and compressive strength, it is suited for paved and slabbed surfaces used with up to heaviest loads. It features high water permeability and frost resistance. STEIN TEC® Bedding Mortar BM 04 meets resp. surpasses with its properties the requirements according to the FSGV-Arbeitspapier Nr. 618/2 (working paper for surface pavements with pavings and slabs using bonded construction).
STEIN TEC® Bedding Mortar BM 04 is optimally adapted with its material properties, like shrinkage and deformation characteristics, to STEIN TEC® jointing mortars.
The thickness of the bedding when compacted, shall be 4 cm and, single-layer, 6 cm maximum. If the bedding thicknesses is more than 6 cm when compacted, it is necessary to pre-shape in layers under approx. 25 % pre-compaction (required gross density of hardened mortar 1.900 kg/m³, cp. Table “Technical specifications”).
- high compressive strength
- high adhesive tensile strength
- high water-permeability
- low-shrinkage and low-stress
- polymer modified
- very good processability
If concrete blocks, slabs and, in general, elements with smooth and even (e.g sawn) underneaths are used, STEIN TEC® Bond Adhesive Haftfix should be applied additionally.
Paving blocks and slabs must be clean, i.e. free from dust, grease, oil, adhesions and impurities (e.g. cutting or grinding slurry).
For the laying and grouting of paving blocks and slabs in bonded construction method, respective regulations and generally accepted codes of practice do apply, like DIN 18318, ZTV Pflaster-StB (about pavings) and the bulletin M FP as far as applicable to bonded construction method and to the FSGV-Arbeitspapier Nr. 618/2 (working paper for surface pavements with pavings and slabs using bonded construction). Especially important is a sufficiently stable superstructure suited to the expected loads. For traffic areas where heavy traffic is expected, the requirements in terms of design and sustainability should be set for the panel 3 (Construction Classification III according RStO 01) or Load Classification 3.2 according RStO 12.
STEIN TEC® Bedding Mortar BM 04 shall be mixed either using the horizontal flow-mixer mounted at the silo, or if delivered as bag ware in the positive mixer with clear cold water only (added amount see Technical Bulletin or imprint on bag) in earth-moist texture (snow ball test see under “Information”). On the bedding, the paving blocks resp. slabs shall be finally hammer set in correct height and alignment in projected joint distance. By the piling strike, a compaction of approx. 25 per cent of the mortar bed, professionally prepared, must be achieved underneath the element (required gross density of hardened mortar 1.900 kg/m³, cp. table “Technical specifications”). The mortar bed must be raised up by that slump.
The paved / slabbed surface must be after-treated. For further information see Technical bulletin STEIN TEC® Bedding Mortar BM 04.
BEDDING MORTAR BM 04 Binding agent base hydraulically binding specialty cements Minimum processing temperature 5° C, night-frost free Processing time approx. 1,5 hour at 20° C Requirements approx. 20 kg dry mortar / cm / m2 Built-in thickness at least 4 cm, single-layer 6 cm maximum in compacted condition Compressive strength after 1 day (20° C) * > 10 N/mm2 Compressive strength after 7 days (20° C) * > 15 N/mm2 Compressive strength after 14 days (20° C) * > 20 N/mm2 Compressive strength after 28 days (20° C) * > 30 N/mm2 Adhesive tensile strength1) > 2,0 N/mm2 Gross density of hardened mortar 1.900 kg/m3 E-module < 20.500 N/mm2 Water permeability > kf = 10 x 10-5 m/sec Frost resistance proven eduction of sound run-time after CIF test CIF Testing fluid distilled water < 5 % All values determined on the basis of lab-body blocks in build-in density at 20° C at the specified testing age resp. after 28 days.
1) Determination of adhesive tensile strength on slab base-body according to DAfStb-guideline “Schutz und Instandsetzung von Betonbauteilen, Teil 4 (= Protection and reinstatement work of concrete elements, part 4) with “Haftfix”.
Subject to technical modifications.
Suitability for storage approx. 6 months in the silo and as bag ware in dry cool rooms.
* The decrease of temperature down to 10° C doubles the needed time for hardening. At the decrease down to 5° C it will be quadrupled.